Device addresses are based on the zone numbers being used, as shown below. Expander Module Addresses For Zones… Do not install within the control cabinet. Remove the ohm EOL resistor if connected across the selected zone. Mount either remotely or in the control panel. Use or modules.
Use standard 4-conductor twisted cable for long wiring runs. Install the powerline carrier devices according to the instructions included with each. See connections diagram in the AC Wiring paragraph for connecting the X10 transformer. Connect incoming phone line and handset wiring to the main terminal block via an RJ31X jack as shown in the Summary of Connections diagram at the back of this manual. Wire colors represent the colors of the cable to the RJ31X jack.
One diagram shows connections when a Phone Module is used, the other shows connections when the is not used. Connections use one of the on-board triggers. Disarming the system within the two minutes stops the alarm sound and displays " See Output Programming section for procedures. Zone List Menu Mode Use the menu mode to define zone lists.
See Zone List Programming section. Swinger suppression applies to burglary Entry 1: No. For full installation and programming information, please refer to the. Previous Page. Next Page. Adt focus plus commercial fire and burglary alarm system user guide 88 pages. Commercial fire and burglary security system with scheduling pages.
In most ADT control panels, these touchpad panic buttons are defaulted to be both active and audible for residential installations. To Enter Programming Mode: Local programming requires the use of a Custom English touchpad connected to the touchpad terminals on the control.
Page 5 Enter the number of digits shown. Do not fill unused spaces. Enter up to 20 digits. Touchscreen Compatibility Note: To To enable a touchscreen, enter the option corresponding See table at right for entries. Connect incoming phone line and handset wiring to the main terminal block via an RJ31X jack as shown in the Summary of Connections diagram at the back of this manual.
Wire colors represent the colors of the cable to the RJ31X jack. Connect Phone Module terminals as shown. Use an RJ31X jack with a direct-connect cord and make all connections exactly as shown. Compatibility: Phone Modules must have software version WA The wiring diagram shows the wiring connections that will provide proper operation in most cases.
Connection to the incoming telco line via a RJ31X jack and direct-connect cord, as shown, is essential, even if the system is not connected to a central station.
The will not function if this is not done and an error signal fast busy signal will occur when trying to access the system via the phone.
The house phone lines gray and brown wires must be wired to the phone module terminals; not to the control terminals. Otherwise, an error signal fast busy signal will occur when trying to access the system from an onpremises phone. R GREY. Refer to the connection diagrams below. One diagram shows connections when a Phone Module is used, the other shows connections when the is not used. The following is a summary. As shipped, the AVS-ADT Base unit board comes premounted on its mounting bracket, which is designed to mount inside the control cabinet.
Secure the assembly to the cabinet using the two self-tapping screws provided. The AVS-ADT Base unit board has several terminal blocks for making connections to remote stations, telephone lines, and to the control panel.
See the diagram on the next page for specific wiring connections. Connect all other ECP devices touchpads, expander modules, etc. If using a GSMV module for 2-way voice operation, install the module according to its instructions.
NOTE: The module must be mounted within three feet of the control. The audio cable is supplied with the GSMV module. Complete all other GSMV wiring following the instructions included with that module. Install the AVS module according to its instructions. Use data field 55 Dynamic Signaling Priority to select the desired reporting paths.
The following is a list of the various Programming modes used to program this system:. The system supports up to 64 zones plus three emergency zones numbered 95, 96, and Refer to those sections for detailed procedures. The system can control two independent areas of protection known as partitions for use by independent users, if desired, by simply assigning zones to one or the other partition during zone programming.
The system, by default, automatically distributes users between the two partitions. The master user can change the user number distributions. Zones can also be assigned to a common partition, which is an area shared by users of both partitions such as a lobby in a building.
This allows either partition to arm, while leaving the common partition disarmed for access into the other partition.
The common partition functions as follows:. If only one partition is armed, the system ignores faults on the common zone. Set the following touchpad-related data fields as required by the installation:. Once a wireless key is enrolled, it must be assigned to a user before it becomes active. The system can send various reports to up to four pagers. To program pager reporting:.
Enter the appropriate information in the following data fields. System must be armed for the Latchkey report to be sent. If using a function key to manually send a message to a pager, see Function Keys paragraph. You must assign a zone type to each zone, which defines the way in which the system responds to faults in that zone.
Zone types are defined below. In the case of a. A subsequent. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions.
Enter a new password. Safewatch Pro EN. Cabinet and Lock 1. Figure 1. Mounting the PC Board Swing this board into place and secure it with two additional screws. Mounting and Wiring the Control Wiring to Touchpads 1. Determine wire size using the Wire Run Chart on the next page. Supplementary Power optional 1. Figure 4. Sounder Bell Connections 1. For supervised output, continue with steps 2 and 3. Figure 5. Figure 9. Mounting and Wiring the Control Installing a Keyswitch 1.
If the tamper is opened when the system is armed, an alarm will occur. The Ademco keyswitch is UL Listed. Adt Safewatch Pro Installation Manual. Adt safewatch pro security manager security system user's guide 56 pages.
Find your owner's alarm manuals here to download. I was told I can program the system to page my pager anytime a users code is. The alarm does not work anymore and it is telling me to check all zones. The keypad has the ready light on and I can arm the system, but nothing happens when I open the door, like the zones aren't being detected.
I've replaced all batteries and still the same problem. Safewatch Pro. User's Manual. Safewatch Pro.. Great service! The technician Aaron W was so helpful and took all the time I needed to talk me through re-programming my Sky Bell doorbell to the Wi-Fi router after I updated my Internet service.
0コメント