Recommended For: adhering plastic and fiberglass tub and shower surrounds to structurally sound drywall, plywood, ceramic tiles, greenboard and cement backerboard.
Acrylic is the best system to use for shower walls because it is the safest, least high maintenance, and easy to install, meaning your shower could be done in as little as one day.
Acrylic is one of the most durable materials used in the shower construction industry, and for good reason. Insulating behind shower walls improves moisture control, which in turn reduces the chances of mold growth. Apart from retaining heat and minimizing condensation, insulating behind shower walls also provides better acoustics by reducing annoying sounds from outdoors or between rooms.
Shower kits do come in pieces, making it easy to build your shower from scratch. Putting in a new shower stall is not difficult, but you will need someone to help lift the stall onto the drain. After that, you are well on the way to replacing the shower stall. Bore through the drywall with a drill and core bit for small pipes, such as up to 2-inches.
Measure the dimensions of the cut-out if you are cutting for more than just a pipe stub-out. Cut the circle out with a keyhole saw.
The best approach when installing cement board or other tile backer around a tub is to keep the cement board out of the lip area. Tile are a very common way of finishing the walls in remodeled and new baths as they are impervious to water and highly stain-resistant. You can also apply the thinset mortar effectively over the whole wall so as to make sure that the bond for the tiles is a long lasting one.
Mar 24, If you need to replace your drywall after water damage or mold issue, it would be a good idea to replace it with moisture-resistant drywall. Regular drywall will not protect your property from water and mold damage. Moisture-resistant drywall is best suited for areas such as untiled bathrooms and basements where there might be damp conditions and humidity with minimal splashes of water. If so, install the remaining panel before turning to the front wall panel. The final panel is the one containing the plumbing fixtures; this is usually the front wall of the shower.
Before installing this last panel, it will have to be drilled for the tub or shower valve and maybe a tub spout. Take measurements off of the back wall to the center of the valve, and off of the tub or shower base to the center of the valve.
Transfer these measurements to the tub surround panel. Measure very carefully, as there is no fix if you drill the holes incorrectly. Drill holes in the surround panel using a drill and hole saw. For the faucet valve hole, select a hole saw bit that is large enough to accommodate the trim screws as well as the shower valve the faucet escutcheon plate will cover the slightly larger hole.
For the tub spout or shower arm, choose a hole saw just slightly larger than the stub-out pipe. When drilling the holes, it helps to set the drill to rotate in reverse, since this prevents the teeth of the hole saw from ripping the acrylic panel. The pilot bit will help keep the hole bit in place while the hole is drilled. Once all of the holes are drilled in the last surround panel, check to make sure they line up with the plumbing stub-outs before locking it in place permanently.
If the measurements were slightly off, make small adjustments until the holes line up correctly. Then lock the panel into the back wall and level it up. Screw or nail the panel's flanges to the studs after drilling pilot holes. Finish by completing any wall patching that is necessary, then install and caulk the plumbing handles, escutcheons, and trim. If the directions say so, also caulk the seams between panels, and along the shower base or the edge of the tub.
Let the caulk cure as directed usually at least 24 hours before using the shower. Actively scan device characteristics for identification. Use precise geolocation data. Select personalised content. Create a personalised content profile. Measure ad performance. Select basic ads. Create a personalised ads profile. Select personalised ads. Apply market research to generate audience insights. Measure content performance. Develop and improve products. List of Partners vendors. Project Overview.
Featured Video. Materials Tub or shower surround kit Tub-and-tile caulk Roofing nails or utility screws. Prepare the Walls Unless the studs are already exposed, installation starts by stripping the walls down to the studs around where the surround will sit. Tip Make sure the installation is done according to the manufacturer's instructions. Tip When drilling the holes, it helps to set the drill to rotate in reverse, since this prevents the teeth of the hole saw from ripping the acrylic panel.
Show Full Article. Your Privacy Rights. To change or withdraw your consent choices for TheSpruce.
0コメント